Login/Register
Hint: separate multiple terms with commas
Date
E.g., 02/26/2021
Date
E.g., 02/26/2021
Global
Global
China (简体中文)
Japan (日本語)
Korea (한국어)
Taiwan (繁體中文)
TI training & videos >
Applications & designs
Live training
Products
Tools & software
Toggle navigation
Hint: separate multiple terms with commas
Date
E.g., 02/26/2021
Date
E.g., 02/26/2021
Global
China (简体中文)
Japan (日本語)
Korea (한국어)
Taiwan (繁體中文)
Email
Spin Brushless-DC Motors with the DRV10974
[TEXAS INSTRUMENTS JINGLE] Hello. In this video, I will illustrate how to quickly spin your brushed DC or BLDC motor using Texas Instruments' new DRV10974 evaluation module. The DRV10974 is a fully integrated three-phase brushless DC motor driver that uses TI's proprietary through 180 degrees sensorless algorithm. This enables customers to design a low-noise and highly efficient motor system with minimal external components and to create a more robust and compact board. Now that we understand a bit more about the DRV10974, let's get started. Connect the power supply to the EVM by attaching a ground wire to the test points labeled GND and apply a voltage output between 4.4 volts to 18 volts to the test point labeled Power In. Make sure the current of your supply is set to 1.5 amps, and make sure the switch S1 is in the off position. Next, let's power up the board and turn S1 to the on position. The motor should start spinning. The motor speed can be controlled either by changing the analog voltage through changing the potentiometer or configuring the shunts on the J3 header and applying PWM them signal to the PWM In test point. Some motors require additional configuration to get the motor spinning. One way is to change the current limit resistor on the current limit settings or CS pin to a value lower than 1.5 amps. Additionally, the lead time settings or resistor can be reduced or increased by placing the resistor on the ADV pin. Note that changing the resistor value on the RMP pin will change the acceleration profile of the DRV10974, but the settings should only be changed after the CS and ADV values are selected to get the motor spinning. These resistors can be installed by replacing the 0603 resistors, R2, R3, and R4 for ADV, RMP, and CS, respectively, or installing through-holes resistor into jumpers J8, J9, J10. See the CS, RMP, and ADV resistor selection section in the DRV10974 EVM user guide for more configuration details. To learn more about the DRV10974 and how it can help optimize your BLDC motor system, check out the product folder at ti.com/product/DRV10974. Thanks for watching.
Description
September 10, 2018
In this video, we will demonstrate how to spin motors using our newest brushless-DC motor driver, the DRV10974.
Additional information
Learn more about TI motor driver solutions
Ask questions and interact with the authors in the TI Motor Drivers Forum on the TI E2E™ Community.
Related courses and events
01:07
InstaSPIN-MOTION in Action: CNC Machine
02:02
Ask the Expert: What does the ISP in TDA3x processor do?
02:06
TI Take our Daughters and Sons to Work Day - 2016
02:49
Ask the Expert: Does TI offer hardware tools to accelerate development on the C553x ultra-low-power DSPs?
01:44
Educational BoosterPack MKII Board Tour
arrow-top
close
delete
download
menu
search
sortingArrows
zoom-in
zoom-out
arrow-down
arrow-up
arrowCircle-left
arrowCircle-right
blockDiagram
calculator
calendar
chatBubble-double
chatBubble-person
chatBubble-single
checkmark-circle
chevron-down
chevron-left
chevron-right
chevron-up
chip
clipboard
close-circle
crossReference
dash
document-generic
document-pdfAcrobat
document-web
evaluationModule
globe
historyClock
info-circle
list
lock
mail
myTI
onlineDataSheet
person
phone
question-circle
referenceDesign
shoppingCart
star
tools
videos
warning
wiki